Up To 12 Year Worcester Bosch Guarantee

How To Drain A Worcester Bosch Combi Boiler?

Why Draining Your Worcester Bosch Boiler Is Important?

Even though Worcester bosch boilers are known to be the best-branded boiler you still need to ensure they are taken care of properly. There are 3 essential steps to make sure why you need to drain your boiler.

1.You will need to reduce the risks of your pipes freezing.

Your boiler is going to be turned off for more than 2 months or even 2 weeks as well, so if you want to prevent pipes from freezing you will need to drain your boiler on time.

2.Not cleaning your boiler will increase the risk of water leaks when changing pipeworks or renovating your pipes.

If you want to remove those rusty and unsightly radiators or change your pipeworks, not draining your boiler beforehand can result in a massive flood and damage to your floor and walls.

3.It protects you from paying for expensive boiler repairs and replacements.

The sludge can build up and cause your boiler to fail over time. This is why draining your boiler can eliminate the sludge from your system and keep your boiler in good condition.

Step To Step Guide On How To Drain Your Boiler:

When it comes to draining your boiler here are the key 9 steps on what to do:

1.Unplug your boiler from the mains.

2.Wait 2-3 hours for the water to be able to fully cool down completely.

3.Turn off the water intake valve.

4.Locate the lowest radiator in your home and then try to find the drainage valve, situated on the lowest point.

5.Make sure a hose to the draining valve is well secured so the water exists in your home safely.

6.Open up the valve on top of each of your radiators in your home and wait until there is no more water coming out.

7.Close the bleeding valves and the drainage valve.

8.Locate a braided filling loop underneath your boiler and open it. Then, therefore, let the system repressurise itself to approximately 1 bar. Put the filling loop then back into its place.

9.Therefore the last step is to check for any leaks around the boiler and radiators. If there is none then you have fully accomplished draining your boiler and extended its lifespan.

When Do I Drain My Worcester Bosch Combi Boiler?

Most professional boiler manufacturers will advise you to drain your boiler at least every 6 to 12 months. So doing this will benefit your boiler to get rid of any sediment or any other build-up that collects on the bottom of your hot water tank. As the boiler sludge collects your boiler must work harder which therefore costs more money and a lot more energy is wasted. The best way to do so is to ensure that these issues are performing at regular maintenance which can extend the lifespan to 15 years.

Things To Consider Before You Drain Your Boiler

There is always factors that you have to consider before you drain your boiler such as:

-Before you drain your boiler make sure you are mindful that there is always a risk of leaking after it’s been drained. Sometimes the drain valve won’t close properly after the boiler is drained especially if it’s been sitting for 6 months or longer.

-Always be prepared by getting a cap beforehand just in case it doesn’t close properly. So be ready to put a cap over the valve if needed be. If the valve is made out of plastic you may want to upgrade it completely before turning your water back on.

Why Does My Boiler Keep Losing Pressure?

If your boiler keeps losing pressure, you’re not alone. This is very well known and is a common boiler repair job that requires a quick call to your plumber. There are many reasons why this can happen.

What Is A Boiler Water Pressure?

Boilers are the worst espeically when they have loads of problems in the colder months, espiecally when you don’t have any hot water. When this happens it indicates that your pressure is too high or maybe even too low. Your boiler heats cold water that flows around a circuit of pipes and radiators throughout your home. For it to be effective you’ll have to make sure your pressure is stable.

How To Check My Boiler Pressure?

One of the most common question is how to check my boiler pressure. So for a common modern boiler such as a combi boiler the pressure gauge is around the frnt of your boiler or underneath the control panel. However if you have an older boiler then your pressure gauge is underneath the pipework, if your struggling to find it then look in the instruction manual.

What Should My Boiler Pressure Be?

A normal boiler pressure should be around 1-2 bars. The ideal boiler pressure is often marked as a range within the green area on the gauge itself, whereas red will indicate the low and the high boiler pressure zone. Bear in mind that your boiler will still continue to work, if the pressure is in the red zone.But if your shutting down or won’t snitch on here at Origin we have got you. Even if your boilers working well, it’s a good idea to check your pressure occasionally.

Why Does My Worcester Boiler Keep Losing Pressure?

Your probably wondering why your boiler keeps on losing pressure? Right well here at Origin we will provide you with all of your answers to your questions. One of the worst issues is that your boiler is less than 1 bar on the pressure gauge. Which isn’t an error code but it is a problem which is indiciating that your boiler has low pressure.

There can be many reasons for why your worcester boiler is losing pressure, but bare in mind that it is normal for a boiler to slowly lose its pressure overtime but it can also be caused if you’ve recently bled your radiators. Although if you have noticed a huge drop in your pressure then it might mean you have a leak in your system.

Here is a few reasons for why your boiler may lose pressure:

What Causes A Boiler To Lose Pressure?

  • A leak in the central heating system
  • The expansion vessel has lost its air
  • Pressure relief valve passing water

How To Fix A Leak Within The Heating System

To find a leak within your central heating system, the first step to do is to check all of the radiator valves. The most commonly known place to find a leak is on the radiator valve, an easy way to check is any signs of water or old water damage like stains and rust.

Sometimes you can also fix a radiator leak, which is fixed by tightening one or some of the nuts on the valve. There are 3 places on a radiator valve that can leak from tightening the nut with an adjustable spanner. After fixing the leak, you should be able to bleed your radiators and repressurise the boiler to 1 on the pressure gauge.

If the leak is not on a radiator, you should check your boiler and any of your central heating pipes on show within your house. However if you can’t find the leak anywhere on your heatingsystem, it could be a problem underneath the flooring.

Expansion Vessle

Another reason for why your boiler keeps losing pressure may be due to your expansion vessel. Your pressurised central heating system (combi/system boilers) they all need an expasion vessel. This is when the expansion of water from the heat when the heating system is turned on.

If your system or combi boilers keep losing pressure with no leaks then you may have a faulty expansion vessel which is causing this issue. In order to find these they may be inside your boiler or heating pipes depending on what type of system you have.

The expansion vessel is full of air, so when the heat is on it also takes some of the pressure increase away from the pipes. To fix this solution you’ll need to either recharge your expansion vessel by pumping it up with a pump. Another solution may be that the diaphragm inside the vessel is split and you’ll have to call the plumber to replace the expansion vessel.

Pressure Relief Valve

Another alternative reason for why your boiler is losing pressure could also be due to the pressure relief valve. Ll of the combi boilers and heating systems all must have a safety deviece called a pressure relief valve. This is a device that will protect your centrl heating system from building up with too much pressure and causing radidaitors and boilers to blow up.

In order to fix this solution so your boiler doesn’t lose pressure, you should keep checking your blow-off pipe outside for any dripping water. If it’s dripping therefore you’ll need to replace the pressure relief valve.


Can A Boiler Lose Pressure Without A Leak?

This question is asked a lot and the answer is yes, a boiler can defineinlty lose pressure without a leak. A leak is the most common cause of a boiler losing it’s pressure, however it could alos be due to an expansion vessel problem or a pressure relief valve, or by bleeding radiators.

How Often Should A Boiler Pressure?

A boiler should never lose pressure unless their is a huge issue. If your central heating is losing pressure slowly, then you might notice a small leka within your central heating system.

What Should My Boiler Pressure Be?

Your boiler pressure should be around 1 bar, when your heating is off and the system is cold. However if you notice that it has dropped below 1 bar, then you will need to repressurise your boiler as soon as possible. When your heating is on, it’s normal for the pressure gauge to be around 2 bars.

What Type Of Boiler Do I Have?

A boiler’s type can be incredibly helpful if problems arise that need an engineer’s attention or if you’re replacing an old boiler.
If you have just moved house or haven’t lived on your property for long, we understand that you may not be familiar with your boiler and what type it is. There are 3 types of boilers you can have one of the following :

  1. Combi Boiler
  2. System Boiler
  3. Regular Boiler

Identifying Your Boiler

The easiest way to identify and know what type of boiler you have is to look into your heating system and the components that are installed within your home.

  • Do you have an external pump?
  • Do you have a cold water storage tank in your loft?
  • Do you have a hot water cylinder in your airing cupboard?

What Are Combi Boilers?

A combi boiler is a gas boiler that combines the water heating system and the central heating unit into one body. To be able to produce hot water instantly, which means they won’t need to have a separate hot water tank. They take up less space in your room compared to a system and a regular boiler.

How Do I Know If I Have A Combi Boiler?

To answer all of your questions, most of the time your boiler is probably a combi boiler. To identify if you have a combi boiler, there will be five copper pipes that come from the bottom and there will be no external pump or hot/cold water cylinders.

They’re the most popular kind of boiler within the UK, as it’s made for smaller flats with only one bathroom. This is due to the running hot water from two outputs at once being a lot and will cause chaos.

What Is A System Boiler?

A system boiler controls and heats the central heating system, which produces the hot water for the water storage cylinder. They directly take the water from the mains as opposed to having a feed and expansion tank just like a regular boiler. These boilers are usually found in homes that require hot water.

How Do I Know If I Have A System Boiler?

A system boiler is a bit different to a combi, the best way to identify and tell is to check for copper pipes at the bottom of the boiler, and there should be three. They don’t have an external pump and external expansion storage, as it’s all stored and kept inside the boiler itself.

They’re also known as a sealed system, and most are found within bigger homes that require multiple outlets at once. During the system boiler installation, you won’t receive any hot water instantly just like a combi boiler. It will have to be provided from the hot water cylinder which is found within the airing cupboard.

What Is A Regular Boiler?

A regular boiler is also known as a conventional boiler or heats only, as they don’t provide domestic hot water on demand like combi boilers. Instead, they store hot water in the cylinder until it’s required to be delivered to a tap/shower.

How Do I Know If I Have A Regular Boiler?

You probably have a regular boiler if you have a hot water cylinder, a cold water storage tank, and an external pump. Check that every component of your heating system is still providing your home with heat and hot water, as you would with other boiler types.
You can also check your boiler’s bottom and top pipes. It is common for regular boilers to have two pipes coming from the top and one from the bottom.
Compared to the other boiler systems we have described here, regular boilers take up the most space, but they are capable of supplying hot water to several bathrooms at once, which is why they are most commonly installed in larger homes.

How To Save Money On Your Gas Bill

For many people, gas bills can be the largest single bill they face every month. Thankfully, there are things you can do to save money on your gas bill. From installing energy-efficient LED light bulbs to turning off your electronics when you aren’t using them, you can see significant savings each month with a few simple steps. At Origin, we care about our customers and are here to help you save money on your gas bill, so you don’t have to resort to cranking up the thermostat just yet! We provide plumbing and heating services in Glasgow and wider areas and provide boiler cover to suit your requirements and budget.

How To Save Money On Your Gas Bill

7 Ways To Save Money On Your Gas Bill

1. Maintain Your Heating System And Appliances Properly

How To Save Money On Your Gas Bill
Before considering how to save natural gas at home, you should keep maintenance of your existing systems at the top of your list. Your older natural gas furnace or water heater will likely become less energy-efficient as time passes. But you can make your heating system run more efficiently by having inspections and routine maintenance, replacing parts that leak or break down and limiting your heating bill.

2. Invest In Insulation

Buying the appropriate insulation for your home is a cost-effective way to keep the warmth inside and save money on energy bills. Sealing your windows and doors with caulk or weatherstripping is an excellent first step. One easy way to save energy during cold weather is to cover your windows with curtains or blinds. Additionally, if you insulate your water heater and your doors and windows, you might be able to buy an attic tent to help trap the heat from escaping through your attic.

3. Check For Blockages

The warm air your natural gas heating system produces should be able to flow freely throughout your home. Ensure vents are clear and check your floor plan to ensure bulky furniture or appliances aren’t blocking them. When there is inadequate airflow, your heating system has to work extra hard to heat a home that will not respond to its efforts. The benefit of adequate airflow is that it lessens the burden on your heating system and may reduce energy expenditure.

4. Turn Down The Thermostat

Especially in the winter when gas bills can climb high, lowering the thermostat by a couple of degrees can make a difference, helping you save more. If lowering the heat would make your home uncomfortable in the evenings, try reducing the temperature only at night, or during the day if family members are at work. If you’re struggling to keep your gas bills at a manageable level, have a look at your thermostat settings and see what you can do to adjust them.

5. Keep Doors And Windows Shut

Be sure to keep doors and windows closed when your natural gas heating system is running in the winter to prevent a big bill at the end of the month. In the summer, opening windows and doors can be great for cooling off a hot house, but in the colder seasons, it will let valuable heat escape. Open up your windows and doors to maximise the efficiency of your gas heater and lower your utility bills.

6. Get A Smart Thermostat

Think about buying a smart thermostat for your home. You can program a smart thermostat to automatically heat the house at your designated time, so it won’t keep heating the house when no one is there or when everyone is in bed. This will save you the frustration of forgetting to turn down the heat at night, as well as potentially significant savings on your gas bill.

7. Wrap Up

In the winter, having an extra layer or two of clothing can make it much easier to turn the thermostat down a few degrees and stay warm. Throw on an extra blanket or two, or a down comforter when your thermostat is in energy-saving mode to stay warmer.

Reasons Why Your Gas Bill Is High:

How To Save Money On Your Gas Bill
Here are a few reasons why your gas bill is skyrocketing:

  • You have an old, inefficient boiler
  • Poor insulation
  • Blocked vents and airflow
  • heating costs throughout the year
  • Don’t leave appliances unattended
  • Increased demand for natural gas locally

So that you can see the benefits for yourself and save money on your next gas bill, contact Origin. We offer the energy solutions you need to keep your house running at its optimum efficiency. At Origin, we provide plumbing and heating services such as boiler installation, servicing and repairs. We also do emergency plumbing and other services, check our website to find out more.

When To Replace Boiler

It’s important to keep your boiler in top condition to ensure the safety of your home and family, but the problem is that not all boiler problems are immediately obvious. When it comes to your boiler, safety should be your biggest concern, particularly if you’re not sure when you bought your boiler or are unsure of its age. It’s important to have your boiler inspected by a qualified engineer before using it again and potentially risking injury or property damage. If you’re having any problems with your boiler and aren’t sure what to do, give Origin a call today. In this blog, we will cover 6 reasons why you might need to replace your boiler and offer some helpful resources along the way.

When Should A Boiler Be Replaced?

Here are 6 significant signs to look out for to see if your boiler needs replacing: 

1. Your Rooms Are Cold

If you’re feeling cold, there could be a problem with your boiler. Low temperatures can indicate an obstruction in your heating system, a broken valve or pump or even damage to your boiler itself. If you’re experiencing recurring issues with your boiler, it may be time to replace it with a newer model. Contact us today for more information about how replacement boilers work.

2. Your Boiler Is Too Old

If your boiler is older than 15 years, it’s probably time to replace it. Over its lifetime, there will have been some maintenance issues that will only be resolved by replacing them with a new one. All heating systems will eventually wear out and break down before replacement can result in expensive emergency service calls. So if you have an older model boiler or parts are no longer available, get in touch with Origin today. Our team will gladly install a new boiler for you. No job is too big or small!

3. Strange Sounds Or Smells

If you notice that your boiler is making strange noises or smells, it’s probably time to call in a professional. The smell of gas is always alarming, so listen out for any unusual hissing or whistling sounds. These can be signs of gas leaks—and that is not something you want in your home.

4. Radiators Take Long To Heat Up

There are few things more annoying than having to sit by a radiator waiting for it to heat up. This is usually a sign that your boiler is either very old or in need of repair. Radiators are primarily used for floor heating, and due to their design, can take a long time to heat up large rooms. It may be that your heating system needs replacing as soon as possible if you have radiators which do not provide adequate heat.

5. Constant Boiler Breakdowns

If your boiler keeps breaking down it could be a sign that your boiler is on its last legs. When parts start breaking more often than they should, it means that there’s a bigger problem to deal with and usually those problems come with much steeper repair costs. If you keep getting repairs, schedule some time to get an inspection so you can assess what’s really wrong and how much it will cost to get everything up and running again. It’s important to get your boiler serviced annually to avoid any costly repairs.

6. Look Out For Yellow Flame Colour

If you want to ensure your boiler will last a long time, you’ll need to take note of how its flames look. The colour is often an indicator of how well it’s functioning. Blue flames mean everything is working fine, while orange and yellow flames signal problems that could cause major damage. However, a common sign of an ill-functioning boiler is black smoke coming from its exhaust vents; if you see smoke pouring out, get in touch with your local engineer before more serious issues arise.

The Importance of Regular Maintenance

Generally, boilers are extremely reliable and don’t need a lot of TLC, but there are situations where you may need to contact us. Letting these problems go untreated for long periods of time can cause irreparable damage to your boiler and put you and your family in danger.

A boiler is one of the most important parts of your heating system, making it essential to have it inspected regularly by professionals . If you notice any of these signs above, call one of our engineers at Origin to conduct a proper inspection and give you the correct advice and guidance about boilers. Your home should be your sanctuary from the outside world, so you need to be sure that it’s being well maintained all year round.

Are Your Clean Undies Ramping Up Your Bills in 2022?

Are Your Clean Undies Ramping Up Your Bills in 2022
It is not a secret that our gas and energy bills have been rapidly increasing over the last few years, and many homeowners across the UK have had to struggle financially to keep up with the new energy prices implemented by the government. The price increase is due to a large rise in wholesale gas prices (the amount energy companies pay), which has climbed steeply since October 2021. Due to the global economic downturn as well as the end of the lockdown, gas prices have reached the highest they have ever been, and may continue to rise in the upcoming years.
But not to worry, we are here to assist you. There are many rules and tips that can help make your life easier by lowering your heating bills. In this article, we will be looking at:

  1. Why Are Energy Costs Rising? 
  2. Who is Ofgem?
  3. What Is The Average Household Energy Bill?
  4. How to Reduce Heating Costs 
  5. Ground Source And Air Source Heat Pumps

Why Are Energy Costs Rising?

People are concerned about the cost of their energy bills following the energy crisis and the skyrocketing gas prices. According to UK Power, today’s gas prices are about four times higher than they were in 2020. Because of this, energy prices are expected to plummet, putting 22 million households across Britain at risk. 

Many global factors have contributed to the rise in prices, including increasing demand after lockdown and other financial issues Britain has recently had to face within the last years. 
Why Are Energy Costs Rising?

Did you know that the biggest contributor to UK household carbon emissions is household heating? They produce more carbon dioxide emissions than any other human source – even more than transport!

Who Is Ofgem?

Ofgem is the Office of Gas and Electricity Markets, which protects consumers and creates a greener, fairer energy system. Ofgem set a cap on 1 April 2022 that limits how much energy suppliers can charge per kWh of gas and electricity to their customers. The cap is supposed to limit the amount energy suppliers can charge. A new cap was announced on 3rd February 2022, with an increase of almost £700 for customers paying by direct debit on a standard default tariff. Due to underlying market costs, the cap is subject to increase or decrease.

Those who are on fixed tariffs, where they pay a fixed amount for energy every month, will not be affected by the cap. The cap protects those with a standard variable deal by limiting how much their provider can charge. However, if you use a lot of energy, you might end up paying more than the cap.  

What Is The Average Household Energy Bill?

Property Size Average Household Usage(kWh) Average Annual Cost* Average Monthly Bill 
1-2 bedroom house  Gas: 8,000 kWh/ Elec: 2,000 kWh  £1,178.16 £98.18 
3 bedroom house Gas: 12,500 kWh/ Elec: 3,000 kWh £1,793.21 £149.43
4-5 bedroom house Gas: 18,000 kWh/ Elec: 4,500 kWh  £2,623.66 £218.63

This data is estimated by Ogfem and is based on the amount you spend both monthly and annually with regards to energy prices. Last Updated 3rd February 2022.

As you can see, the average costs for gas and electricity can vary based on your type of household.

  • If you live in a 1-2 bedroom house, you typically use 8,000 kWh on gas and around 2,000 kWh on electricity, with the annual cost of £1,178.16.
  • For those who live in a 3-bedroom house, you use around 15,000 kWh of energy usage on both gas and electricity, with 12,500 kWh being used for gas and 3,000 kWh of electricity, with the annual cost of £1,793.21.
  • For a homeowner of a 4-5 bedroom house, the average annual cost for both gas and electricity is estimated to be 2,623.26, with a calculation of 18,000 kWh on gas and 4,500 kWh on electricity.

At Origin, we are able to offer you the greatest deals that reflect what you will pay for energy more accurately every month, depending on the information given to us. For more information on our services, feel free to contact us..

How To Reduce Heating Costs

There are a number of ways in which you can reduce your energy costs, both gas and electricity. In order for you to live comfortably and be able to afford your energy bills each month, there will be times where you may have to invest – as it will benefit you in the long run. Here are some great ways to reduce your energy bills throughout the year:

1. Clean Your Radiator System

In order to maximize the efficiency of your heating system, ensure that the water in your system is clean and free of sludge. If some of your radiators take a long time to heat up, or if you have cold spots at the bottom of your radiators, this may be a sign that your system is overly sludgy.

How To Clean Your Radiator System

  1. Gravity Flush: In a gravity flush, the water in your radiator system is drained and replaced with clean water. If you’re a competent DIYer, you can do it yourself.
  2. Power flush: A power flush can remove sludge from your system more effectively, but it does require special equipment and can be costly.
  3. Chemical flush: Chemical flushes are less expensive than full power flushes since they don’t require high pressure equipment to clean the radiator. A chemical flush softens the muck and eases it out more gently.

Clean Your Radiator System

2. Boiler & Heating Control Upgrade

Boiler installations can be beneficial for those interested in reducing their energy bills, as an upgraded heating system can be more energy efficient than your old, traditional boiler and can also reduce your carbon footprint.
Replacing a boiler is one way to upgrade your heating system, however this can be quite an expensive alternative. It could cost you up to a minimum of £4,000 for a new boiler installation. The simplest thing to do if you decide that replacing your boiler would be too costly but your heating controls are old is to replace them – newer heating controls are more accurate.

Depending on your type of boiler or heating system will determine what type of heating control measures you need for your household. Here are the main types available:

  • Timer – turns your boiler on and off according to a set schedule.
  • Programmer – Using the programmer, you can set different times and temperatures for different days of the week.
  • Weather Compensation for Heating Controls – regulates boiler operation according to outside temperature.
  • Load Compensating Thermostat – Adapts boiler operation depending on inside temperature based on a load compensating thermostat
  • Room Thermostat – Temperature sensors in the room measure the temperature of your room and adjust the boiler operation accordingly (temperature sensors are load compensating thermostats).
  • TRVs (thermostatic radiator valves) – allow you to control the temperature of individual radiators as well as turn them all off at the same time .
  • Smart thermostat heating system – controls heating remotely via an app.

If you are looking for a boiler installation in Glasgow, we are here to help. We are also able to repair, maintain and service your traditional heating system. Feel free to contact us 7 days a week, 24 hours a day.
Boiler & Heating Control Upgrade

What Other Ways Can I Reduce My Energy Bills?

Keep on top of energy bills

According to Ofgem’s calculation, the cap on out-of-contract tariffs rose 54% in April 2022, meaning the majority of households are now faced with much higher energy bills than they were previously. By staying on top of your bills, this will help you save money if you’re spending far more than you’re supposed to. By investing in something as small as a smart meter, this will help you keep track of the amount of energy you consume.


As reported by  Which.co.uk, by insulating a typical three-bedroom semi-detached house to 270mm, you could save £135 a year on energy bills, because less heat will escape through the roof, and by insulating cavity walls, a semi-detached house can save £155 a year. In the same type of house, solid-wall insulation would save you £210, but is more expensive to install.

Semi-detached house  Detached House Mid-terraced house Bungalow Mid-floor hat 
Cavity Wall Insulation £155 £255 £95 £105 £75
Loft Insulation (0-270mm)  £135 £315 £125 £75 N/A
Draught Proofing £25 £25 £25 £25 £25
Floor Insulation £40 £70 £30 £55 N/A
Solid Wall Insulation £210 £350 £130 £140 £105

This data is estimated by the Energy Saving Trust for England, Scotland and Wales and is based on the amount of costs it takes to insulate your home. It was last updated in September 2021.

Electric Heaters

For those who live in a one-bedroom house, a portable electric heating system may come in handy every now and then. If you work from home or live solely on your own, this could be a beneficial investment, helping you save costs on heating bills.
However, be mindful of the fact that electricity is far more pricier than gas per hour, so you must use the electrical heater efficiently so that your electricity bill does not increase each month.

Light Bulbs

By investing in the correct lightbulb, you could be saving a decent amount on energy bills each year. LED light bulbs are a great way to save money on our electricity bill, as they last longer than traditional light bulbs and cost cheaper to run. Over time, you could be saving up to £200 on your electricity bill.

Draught Proof Your Home

You could save up to £25 in a typical home by preventing heat from escaping through gaps around doors and windows, according to the Energy Saving Trust. If you really want to go the extra mile, by investing in professional draught-proofing, you could potentially save far more than £25 per year.
Here are some areas within your household which you are able to draught-proof:

  • Doors
  • Windows
  • Lofts
  • Floorboards & Skirting
  • Chimney/Fireplace

Reduce Your Use Of Hot Water

Regardless of whether you only use your heating in the winter or year-round, water heats up with energy all year long. Using your water meter wisely will reduce your utility bills. You can also use your heating controls to turn your water heating on and off if you have a hot water tank (rather than a combi boiler).
A power shower can use more water in less than five minutes than a bath when it comes to high-volume water consumption. By replacing your old shower head with an echo, you’ll feel no difference in your shower’s power, but your water bill will go down.

There are a few other small things you can do which may help reduce your water bill and other energy costs, such as insulating your hot water pipes which allows your hot water to stay hotter for longer.
Reduce Your Use Of Hot Water

Ground Source And Air Source Heat Pumps

Ground Source And Air Source Heat Pumps

Heat Pumps are a greener, safer and a more efficient way to provide your home with renewable energy. In order to heat your home, heat pumps absorb heat and transfer it to a fluid, which is compressed to increase its temperature. They work by absorbing heat from the environment and transferring it to a fluid. The compressed fluid then transfers heat to the central heating system, which can heat as well as provide hot water.

One major difference between these two types of heat pumps is where they acquire heat: air source heat pumps (ASHPs) utilize the air for heat, while ground source heat pumps (GSHPs) utilize the ground for energy.

Advantages of Heat Pumps:

  • Lower running costs
  • Requires less maintenance
  • Better Safety
  • Reduces Carbon Emissions
  • Provides Cooling
  • Long life-span
  • Eligible for RHI scheme

Disadvantages of Heat Pumps:

  • High upfront cost
  • Difficult to install
  • Questionable Sustainability
  • Requires significant work
  • Issues in cold weather
  • Not entirely carbon neutral
  • Planning permissions required

Government Schemes Which Offer Financial Support

Government Schemes Which Offer Financial Support
Struggling to provide your home with energy? There are a variety of energy schemes and grants which can help assist in paying your energy bills or supporting your renewable heating costs. You may be eligible for:

  • Boiler Upgrade Scheme
  • Government energy grants for your home
  • Cold Weather Payment, Winter Fuel Payment and Fuel Direct
  • Warm Home Discount
  • Energy Company Obligation (ECO)
  • Free insulation deals from energy suppliers
  • The Green Deal
  • Insulation Grants

We can prevent climate change by reducing energy consumption as we move towards a more sustainable net-zero future: it will save us money as well as help us reduce our carbon footprint. You can secure your financial future by knowing how many carbon emissions you produce each year.

How To Lower Your Heating Costs In 2022

How to save money on your energy bills this year

Your energy bill will be quite hefty at the end of the month, and you are probably looking for ways to save money on it this year. Fortunately, there are plenty of ways to save money on your energy bills, from choosing the right kind of boiler to ensuring your home has sufficient insulation in all the right places. The following blog will walk you through how to save money on your energy bills this year, so you can rest easy knowing that your house is warm and comfortable while remaining fiscally responsible. With Origin, you can save money on your energy bills, so make sure to read over these helpful tips!

How to save money on your energy bills this year

How Efficient Is Your Boiler?

How efficient is your boilerThe efficiency of your boiler depends upon a few factors. Remember these four questions if you want to save money on your energy bills:

1. How Old Is Your Boiler?

It is highly probable that your old boiler is less efficient than newer models and is costing you a lot of money over time.

2. Do You Have A Condensing Boiler?

A condensing boiler is much more efficient than standard efficiency boilers, which could lead to significant savings.

3. Do You Have Boiler Coverage?

Regardless of how attentive you are to keep up with your boiler maintenance, if your boiler breaks down you may be left without heating and hot water. And let’s be honest, that’s a huge headache for anyone. Investing in homeowner care plans and boiler coverage could save you a significant amount of money in the long run if you experience any costly repair issues.

4. When Was The Last Time You Serviced Your Boiler?

Getting an annual boiler service helps make sure that your boiler maintains maximum efficiency for a longer time.

The Most Efficient Type Of Boiler

Older boilers weren’t as efficient because they didn’t collect the wasted heat. Modern boilers are more efficient, with their biggest advantage being that they ‘condense’. They use more of the hot air leaving the stove, which makes them more efficient than the older kind.

Here are three types of boilers that run efficiently:

Heat-Only (Regular) boiler – They use hot water storage, which means you will have a water heater and a hot water storage tank. These are a good option for homes with larger amounts of plumbing.

Combi Boilers – Heats water when you need it, which is ideal for smaller homes. Combination boilers are very efficient and economical. The benefits of switching from a conventional boiler to a combi boiler include decreased heating bills.

System Boiler A kind of boiler that is more intricate, meaning it takes up less space and you don’t need a cold water feed tank in the loft.

If you are thinking about getting your boiler replaced, contact Origin today and we can install, repair or service a boiler for you, and get the job done as soon as possible.


Top Tips To Save Money On Heating And Energy Bills

There are many steps that can be taken to make your home more energy-efficient. It’s also a good idea to maximize heat usage from an older boiler and to reduce waste. Saving money and energy isn’t hard. For example, if you time your heating carefully you’ll see significant changes. Specifically, you should time your heating when you’re out of the house. Doing so can prevent unnecessary energy use. Installing double glazing and wall insulation are some of the cheapest and easiest ways to conserve energy, which would save you more money. Some small hacks can do a lot of good, like keeping your radiators uncovered, which increases their heat output and therefore saves money.

Here are a few other things you can do to save money on your energy bills this year:

  • Upgrade your old appliances (eg. boilers and thermostat)
  • Air seal around windows, doors and fireplaces
  • Turn off lights when not needed
  • Seal any cracks in your walls
  • Insulate your home properly
  • Time your heating
  • Choose which rooms to heat
  • Don’t leave things plugged in when they aren’t being used
  • Powerflush your radiators  if there is a build-up of sludge in the radiator system

How Efficient Is Underfloor Heating?

How efficient is underfloor heatingWhen specified correctly and installed in a well-insulated building, underfloor heating is one of the most efficient ways to heat a home. Not only that, but it’s a modern amenity that a lot of people would expect to see in a contemporary property. That said, in a sense, it may have the ability to add value to your home–but there are a few stipulations to keep in mind before jumping headfirst into it.

Heat Efficient

When it comes to heating your home, underfloor heating utilizes radiant heat, whereas, radiators work by using convection to send warmth throughout the room. This process happens once the air, now warmed by the radiator, reaches the top of the room, and once it cools off, it falls downwards to be reheated by the radiator. In the end, this enables warm and cool air to flow throughout the space, while underfloor heating evenly delivers heat and results in great indoor comfort levels.

Low Energy Usage

The even distribution of heat throughout the room means that you’ll have no uncomfortable cold or hot spots; as long as the system is installed correctly, this even distribution is possible. To take an example, pipework must be laid at even, regular intervals. If it is not, then this is a red flag and something to watch out for when installing it.

Lower Running Costs In The Long Term

Installing underfloor heating costs more upfront but you save in the long run. As we already know, with underfloor heating the heat required to warm the home is less, saving money. Maximum savings will be delivered in thermally-efficient homes, as in these cases less heat is wasted by escaping the house.
If you are looking to get your boiler replaced or annually serviced to save costs and be more energy-efficient contact Origin today. We also do other services such as Powerflush and underfloor heating!

How Does Central Heating Work?

Boiler Installation

The central heating system is a mandatory requirement in homes that are usually taken for granted. It can provide heat in our homes when it’s cold outside and hot water for nice warm showers and washing the dishes. If you’re having issues with your central heating, there’s no need to panic! Many people think that their central heating systems are unfixable because they feel the problem comes from the boiler or the radiators themselves. While these components do play a big role in keeping your home warm and cozy, the heart of your heating system is actually in your house’s basement or crawlspace, where you’ll find the actual heat exchanger and other essential parts. At Origin, we offer plumbing and heating services in Glasgow and surrounding areas. Read on to learn more about how central heating works, and troubleshoot any problems that you might be having with your system.

How does central heating work?

How Does Central Heating Work?

How Does Central Heating Work?
Central heating systems are common in most homes and offices. Central heating is a type of heating system in which heat is distributed through pipes or tubes that transport hot water or steam from a central location such as a boiler room to heat exchangers located in rooms throughout your home. Question Mark continuous line one line drawing isolated black on white vector illustration[/caption]Heating systems can be gas, oil, electric, geothermal or solar-powered. Central heating systems are extremely efficient, as they use pipes to distribute warm air into individual rooms.

Central heating systems have radiators and pipework that connect to the boiler. The boiler supplies the heat whilst the pump moves heated water from the boiler to the pipework, to the radiators then returning to the boiler for reheating. It also offers hot water to the hot taps in your house.

There Are Two Types of Boilers:

A conventional boiler: A conventional boiler includes a pump, a programmer, and a room thermostat. The boiler heats water, which is then piped to radiators in every room so that you can keep warm throughout your home.

A Combination boiler: A combination boiler is, as its name suggests, a boiler that has two sources of fuel: oil and gas. Because it has two burners (or heat sources), it can provide both steam and hot water to your home, giving you instant hot water whenever you need it. It’s a popular choice for large residential homes with three or more bathrooms.

How Do Boilers Work?

Boilers burn natural gas to produce heat. You only need a single appliance to provide heat in your home. The water runs across a heat exchanger to consistently heat enough water everywhere. A gas boiler functions similarly to an oil or biomass boiler, as the burner is switched on and off by a heating control.

Inside a gas boiler you have:

  • Gas burner
  • Heat exchanger
  • Exhaust pipe
  • Control technology
  • The pump
  • What Do Boilers Burn?

    Boilers burn natural gas, propane, or oil. Most modern boilers use gas, while older ones may still use coal. Some systems also include a wood-burning stove as a backup in case of power outages. However, it’s not recommended to rely on fireplaces for heating your home year-round. No matter what fuel you choose, be sure to have regular maintenance performed by a professional to ensure that your system is running efficiently and safely at all times.

    How Do Radiators Work?

    Although it’s common knowledge that we use radiators to heat our homes, many people have no idea how they work. That may be because central heating is so commonplace now; many of us don’t even think about it, and simply expect our house to be warm when we walk in after a hard day at work. A radiator works by circulating hot water from your boiler through pipes inside each radiator until they become hot themselves.

    How Do Thermostats Work?

    Thermostats work by measuring the temperature in each room and turning it on or off when they reach a certain point. You probably use an on/off the thermostat, but you might have also seen thermostats that feature a dial with numbers from 1 to 10; in these cases, turning up your heat all the way might set it to 6 or 7. These thermostats are called variable-speed systems and can help you save energy since they turn your AC or heat pump on and off less frequently.

    What Is Commonly Used To Run A Central Heating System?

    Although you can use anything to run a central heating system, for example, hot water, solar heat, and geothermal energy, traditionally most homes in Britain have used oil or gas as their main source of heat. As technology has improved and become more efficient, it is now possible to use air-to-air heat pumps that are powered by electricity to provide your home with central heating.

    Why Does My Central Heating Bill Go Up In Winter?

    When it comes to central heating, there’s nothing more important than keeping warm in winter. That’s why most homeowners keep their thermostats on low or medium at all times, even in summer. Of course, heating bills go up when you turn up your thermostat to full blast, to keep you and your family warm. You can reduce your heating bills by closing your curtains, blocking any draughts by insulating your windows so you can lower your heating and save money in the meantime.

    When Should I Call a Gas Engineer?

    You should call a gas engineer when your boiler or central heating system isn’t working properly. You should also call a boiler engineer if you want to install a new system in your home and want to ensure everything is installed correctly, which will save you both time and money. If you notice that your boiler is leaking, be sure to contact an emergency plumber immediately!

    How Can Air Get Into a Central Heating System

    In a central heating system, the heat produced by a boiler is distributed to radiators around your home using a network of ducts. Before it gets there, though, it’s warmed up by another piece of equipment called an air heater. This warms up air—also known as secondary air—which travels from room to room and into your radiators. A coil at the bottom of each radiator absorbs heat before warm air circulates back into your home through gaps in wall panels or floorboards. There are two types of central heating systems; forced-air and underfloor heating—and they work in different ways. Underfloor systems rely on hot water heated by a separate boiler to warm radiators via pipes laid beneath a concrete slab or boards laid directly onto subfloor joists.

    How to Get Air Out of Central Heating System

    There are a few steps you can take to get the air out of your heating system. A poor seal between pipes or valves, or between valve and pipe in radiators, can be remedied by forcing water under pressure through these areas. This tends to force any trapped air out. By opening taps in all accessible radiators, filling them with water, and waiting for a short time before turning them off, you will have taken care of most small leaks.

    Central Heating Maintenance

    If you want to make sure your central heating works effectively and efficiently, then you must undertake regular maintenance on your boiler. Neglecting a clogged condenser or dirty air vents will result in damp, stuffy rooms, which can be detrimental to health; therefore, getting your boiler serviced is a must. It also makes sense to service it at certain intervals as recommended by manufacturers and local technicians. Ask them for advice on when annual checks are required and what they involve.

    How Many Litres In A Central Heating System?

    There are a few ways to figure out how many liters your central heating system holds. If you have an electric boiler, it may be possible to use a digital meter to measure up your boiler’s volume. Your home may also come with a manual that includes basic information on your central heating system, including its capacity. If not, speak with a plumber or engineer who can access inside information about your Central Heating System and will know if there is room for improvement.

    Central Heating Services Glasgow

    Often, during wintertime, your home is going to have a problem with freezing. To be safe in such situations, you should get in contact with Origin. We provide central heating services such as boiler installation, servicing, and repairs. If you are experiencing any problems do not hesitate to reach out, we are here to help you.

    How To Drain Down Central Heating System

    How to drain central heating system

    TL:DR – See Summary

    1. Switch your central heating system off (for a safety measure)
    2. Cut the water supply to your boiler
    3. Find your drain off valve on your radiator
    4. Bleed your radiators

    If you want to talk to a professional and get your heating reviewed and fixed in less than 24 hours give us a call now; we are open 24 hours 7 days a week!

    You may have heard people talk about bleeding, venting, or draining your radiator when you have heating problems. But what does draining your radiator actually mean and how will it help? No problem Origin GPH has you covered!

    If you are a homeowner, it is important to maintain your heating system to ensure its efficiency and to avoid any issues. Therefore, it is a good idea to drain your heating system once in a while to remove sludge or repair a leak or change the radiator. Knowing how to drain your radiators and your boiler will keep your central heating system working at full capacity for your home. At Origin, we are experts at fixing, servicing, and installing heating systems.

    How to drain central heating system

    How to Drain Down Central Heating System

    Step 1: Switch your central heating system off (for a safety measure)

    Homeowners, before you start draining anything please switch off the system as a safety measure and wait until the pipes cool down completely. You want to ensure you don’t burn yourself with hot water. If you are about to do a boiler replacement or restoration let them cool also.

    Step 2: Cut the water supply to your boiler

    This step is important because you want to stop water from entering the radiator you are working on, this will prevent buildup as you work. Within most UK homes there should be a separate stop tap for this. However, if there isn’t one or you find it hard to turn it, simply stop the water flow by tying up the ball valve to a wood laid on top of the cistern. The ball valve is what controls the water entering the cistern

    Step 3: Find your drain off valve on your radiator

    A drain off valve is a useful drain point for your radiators and it is usually located on the bottom floor. To help keep mess to a minimum it’s important to drain off the water to the outside. Consider using a garden hose and clip it with the help of a clip to the outlet, so the water runs outside. If you are garden conscious you may want to direct the hose away from plants as there are chemicals in the inhibitors. If you don’t have a garden or a hose pipe a bucket will work. Just ensure you shut off the valve when you need to empty your bucket to avoid mess.

    Step 4: Bleed your radiators

    Now we need to drain the central heating. This can be done to clean out sludge and limescale as well as when replacing your central heating system. Open bleed valves so the water runs through the system freely without blockage. To ensure free-flowing, start with the upstairs radiator and then the radiators on the bottom floor. Again, ensure you have your bucket or hose attached at the end of the drain off valve to avoid mess. If you have air within the system that is preventing the water from flowing. Add more water to fill the tank and loosen the valve that was previously tied up. If this doesn’t work, consider giving us a call.

    How To Drain Central Heating System Without Drain Valve

    A drain valve is used for draining your heating system, but if you do not have one then follow these steps:

    1. Switch off your heating system and cut off the water supply
    2. Wait for the boiler to cool and discharge the water
    3. Separate the radiator by the system – close the two valves. If you have a lockshield, remove the plastic cap and use pliers to close the valve back tightly
    4. Bleed your radiators
    5. Loosen the coupling nut and place a bucket under it with old towels
    6. Rotate the nut anticlockwise until you see the water start to spill into the bucket
    7. Attach a hose then drain the system


    How Long Will It Take To Drain a Central Heating System?

    Usually, it should take between 10 to 15 minutes, however, this depends on the size of your house and how many radiators you have. The more radiators you have, the longer it will take to drain down central heating. To speed up the process, systematically open the bleed valves on every radiator in your home. If you have a drain-off valve it can take 20 minutes to an hour to complete.

    How Often Do I Need To Drain My Central Heating System?

    Boilers can break down regularly, roughly 20% of boilers can break down in a given year. However, one of the silent killers of boilers are sludge and limescale build up. If you want to save money on costly repairs and extend the lifetime of your boiler. We recommend draining your boiler system once a year; keeping your boiler happy and your pockets full!

    Do You Need To Turn The Water Off If You Have a Combi Boiler?

    No. You don’t need to just turn the heating off so there’s no power to the boiler. If you want to drain your combi boiler, after turning off the boiler and disconnecting it from the power supply, wait until the water has cooled down. Then connect the hose to the drain valve, all the bleed valves need to be opened to let all the air escape, start from the highest level in your home, and open radiator valves. You should hear air coming out of the radiator. Open the drainage valve using a wrench or spanner, and expect some water to come out. Once the water is gone, close the valve. When they are all emptied, you have successfully drained your central heating system.

    Contact Us If You Need Help With Your Boiler

    The above will help keep your heating system operating efficiently and will save you money from repairs in the long haul. If you found the following information above useful, why not check our other blog on Most Common Boiler Issues and How to Prevent Them. At Origin, we look after our customers. Contact us if you are having trouble with this or any other queries you may have. We cover areas across Glasgow. Our heating engineers are highly trained and experienced to give you the best experience possible. Take a look at our outstanding reviews and see what our customers say!

    Gas Service Engineers Glasgow

    Plumbers East Kilbride

    A gas engineer’s role is to solve gas-related problems. This includes installing boilers and fixing them, replacing them when they break down. They also work on other gas appliances in both domestic and commercial environments. Before calling up a gas engineer, make sure they are Gas Safe registered and are registered to work on your type of gas appliance as this is a legal requirement. At Origin, we deliver high-quality services to all of our customers through our Gas Safe engineers across Glasgow, covering areas such as Kings Park, Bearsden, Uddingston and Rutherglen.

    Gas Service Engineer Glasgow

    Tasks Gas Engineers Work On But Are Not Limited To:

    • Gas engineers install and/or repair gas appliances
    • Diagnose and repair heating systems
    • Provide quotes for customers, discuss boiler issues and cover options
    • Running checks and tests to make sure the gas appliances are safe and working
    • Joining, bending and cutting pipes to fit them together

    Types of Appliances Gas Engineers Work On

    Gas engineers work on appliances such as gas boilers, cookers, hot water storage cylinders, central heating systems and gas fires, to name a few. Remember that some are only licensed to work on gas meters for instance, whilst others could cover all types of work. The gas engineer should be able to show an ID card to prove this to make sure they are legitimate.

    Difference Between a Plumber and a Gas Engineer

    Gas engineers and plumbers can sometimes seem to be quite similar but there are some key differences. A heating engineer operates with heating systems such as boilers, radiators, thermostats or hot water cylinders. A plumber, however, works on water appliances such as taps, sinks and toilets. They can work on radiators and pipeworks but they cannot work on the boiler itself. They do not hold Gas Safe qualifications, unlike heating engineers. If you require any assistance with your central heating system leave it to the gas engineers. At Origin, we are here to help you with any of your boiler troubles, so get in touch with us straight away and we will send one of our highly trained engineers to sort out the problem.

    Gas Service Engineer For Your Boiler Installation

    If your old boiler is costing you higher bills and poor heating output then it is time to replace your boiler. Having your boiler installed efficiently and correctly is essential for preventing any unnecessary repairs or system breakdowns. We are experts in boiler installations. Installing a new boiler is a huge investment and will be costly. That’s why at Origin we offer cheaper boiler plans through our comfort club. Having a boiler installed takes around 45 minutes to one hour. This is due to the number of things that they have to check, for instance, checking the boiler sensors, combustion chamber, the safety devices and so on. Remember that safety is important, so avoid touching any part of the boiler and leave it to the experts. Our engineers across Glasgow always provide customer satisfaction through our work and are professional, reliable and will get the job done.

    Gas Service Engineer For Your Boiler Servicing

    To prevent your boiler from breaking down, keep up with boiler maintenance to keep your house warm, especially during the cold Scottish winter. It is important to get into the habit of checking your boiler pressure and have your boiler serviced annually even when your boiler is working correctly as anything could go wrong at any given time. Not only this but having regular boiler servicing minimises the risk of carbon monoxide poisoning. A gas engineer will come and carry out several checks and inspections involving checking for any leaks and ensuring that your boiler is working efficiently. Our team at Origin is waiting to help.

    Gas Service Engineer For Your Boiler Repair In Glasgow

    We understand the inconvenience of a boiler breakdown, especially if there is no hot water and it is chilly outside. If your heating system is making weird noises or your radiators are cold this is a sign that your boiler is not working correctly. There are many reasons why a central heating system fails to work. It does not always mean a whole new system is required. At Origin, we will advise you on the best way to quickly get your boiler back to its maximum potential.

    Get In Touch

    We understand that no matter how small a job is, it’s important to do it correctly. At Origin, we are boiler experts who can quickly diagnose and check any issues your boiler has. Contact Origin today on 0141 432 0010 and one of our gas safe engineers in Glasgow will come by and help you out quickly and efficiently.